Sign In
Share to:

Sh-p6401 Electro-hydraulic Basketball Stand

Quantity:

Product instruction

SH-P6401 Electro-hydraulic basketball rack

Dec.2018







SHUHUA SPORTS CO.,LTD

Add:  Shichun Industrial Park, Chidian, Jinjiang, Fujian, China

Service Hotline:800-8585955 400-8878855

http://www.shuhua.com




Content







1. PRODUCT INTRODUCTION

Shuhua basketball rack series are professionally manufactured by shuhua sports co., ltd. The product is designed and manufactured in accordance with the international basketball federation (FIBA) technical standards.Shuhua has been sticking to the mission of “Product intelligence, Sports entertainment and scientific".Shuhua pursues multi-brands strategy in domestic market, with two brands, SHUA and BANCON.Shuhua provides a variety of fitness equipment products and is one of the most complete industrial chain of enterprises.

The basketball rack base is welded with 6mm iron plate. The upright post is welded with 150×70×3mm rectangular tube, 120×120×3mm square tube, 120×70×3mm rectangular tube. The weld surface is uniform and smooth. In order to enhance the safe use of basketball racks, the weight of each basketball rack should not be less than 560kg.

2. Main functions and exercise methods

★  Main Function:Exercise the muscles and strength, as well as the ability to bounce.

★  Exercise Methods:Playing basketball.

3. SAFETY USAGE INSTRUCTIONS

This equipment is suitable for competitive basketball and practice basketball.

 The equipment should be under the supervision of adults when used by minors.

 Basketball rack should be operated by a special person. Please be familiar with the instructions carefully before operation and strictly follow the instructions.

 It is forbidden to move the basketball rack when the basketball rack is in the rising state, and climbing is prohibited

 When the basketball rack is in normal use, the bumper shall be locked, and the bumper shall be released before the basket rack is lowered.

 When the basketball rack is lifting, No one is allowed to stand under the crossarm.

 When the base pulley is lifting, beware of putting your hands or feet under the base.

 The weight of the basketball rack should not be less than 560kg, to ensure the stability of the basketball rack, it is strictly prohibited to use the basketball rack in the case of insufficient weight.

 Cable specification 2×1.5mm2,rated voltage 220V,and ensure that the output power of the cable output end is not less than 0.75kw, so that the electrical function works normally

 M46# hydraulic fluid is recommended for basketball racks.

 Do not hit the boards with hard or sharp objects to avoid damaging them.

 When installing high strength safety glass backboard, pull bar cannot be forced to push or pull, so as not to damage the backboard.

 Regularly check the fastness of all parts of the basketball frame, and tighten the connecting parts or replace the new parts if loose.

 Each year should be regularly (recommended twice a year) check the basketball rack connection (welding) part of the degree of corrosion and firmness, such as the use of abnormal basketball rack, please immediately stop using, and check and repair the normal before use.

 When clean the basketball rack surface should use neutral detergent, so as not to damage the basketball rack spray plastic.

 Please exercise according to your own physical condition. If you feel unwell, please stop training immediately and consult your doctor. After you recover, you can contact again.

 The production date of this product is in the product label, and the safe use period is 8 years.

4. SPECIFICATION DATA SHEET

1.Main Frame

Electro-hydraulic basketball rack is composed of base, post, arm, rear post, pull bar, rebound bar, head moving parts, glass rebound, basket, insurance mechanism, power unit and hydraulic control system.

2.Data sheet

The weight of basketball rack is 1800KG, Dunk impact about 320KG;The inside diameter of the basket is 450mm,The height of the basket along the ground is 3050mm;Rebounding specifications:1800mm*1050mm,The backboard is equipped with the internationally used high-strength safety glass backboard, which has the characteristics of high transparency, good weather resistance, aging resistance, corrosion resistance, not easy to blur and so on. The height of the basket bottom along the ground is 2900mm,The dimensions from backboard front elevation to seat sheath front elevation is 3250mm.

3. Structure diagram


5. ASSEMBLY INSTRUCTION

(1)Basketball rack installation

The following are items used in Assembly Steps. Please make sure the ground is flat and clear. Open the carton and take out the following parts piece by piece and lay in order.


No.号

Name

Q’ty


No.

Name

Q’ty

1

Base frame

1


20

Spring washerφ16

2

2

Front post

1

21

hexagon bolt M12*40

4

3

Back Post

1

22

Flat washerφ12

4

4

Outrigger

1

23

Spring washerφ12

4

5


Safety mechanism

1

24

hexagon bolt M12*35

1

6


6

Upper link of backboard

2

25

hexagon nutM12

1

7








Lower link of backboard

2

26

hexagon nutM8*30

8

8

Backboard field joints(Large)

1

27

flat washerφ12

8

9

Backboard field joints(Small)

1

28

Spring washerφ12

8

3

10

Glass backboard

4

29

Bolt M12*35

2

11

Basket ring

1

30

Flat washerφ12

2

12

Ear piece of Backboard

2

31

Spring washerφ12

2

13

Connector of Lower link

2




32

Bolt M8*30

2

14

Bolt of Lower link

2


33

hexagon bolt M12*80

2

15

hexagon boltM12*35

4


34

Flat washerφ12

4

16

Flat washerφ12

4


35

Lock nutM12

2

17

Spring washerφ12

4


36

Hexagon flange boltsM6*15

4

18

Hexagon socket bolt with cylindrical head M16*40

2


37

Rear post adjusting bolt

2

19

Flat washerφ16

2





Step 1:Remove the hoop cover,Fix the basket ring (11) on the backboard (10) with hex bolts (15), spring washer (16), flat washer (17), adjust the vertical and horizontal alignment of the basket ring and backboard and tighten the bolt. Finally, fix the cover plate of the basket ring on the basket ring with hexagon flange face bolt (36) and finally the basket ring net is installed. (Lock)

Step 2:Remove the backboard field joints (8, 9) fixed at the front end of the outrigger (4) with a 14mm Allen wrench and attach the rebounder to it with hexagon bolts (21), spring washers (22) and flat washers (23),Attach the ear piece of backboard (12) to the backboard with hex bolts (26), spring washer (27), and flat washer (28),Pay attention to the position and direction of the backboard lugs(The folded iron plate is on the inside)。After lowering the basketball rack to its lowest position, raise the backboard to the height of the basketball rack arm extension, and place the bottom edge of the backboard on a solid bracket (self-provided) smoothly. Use hexagon bolts (18), spring washers (19) and flat washers (20) to connect the backboard and the arm extension and fix them. Adjust the bottom edge of the backboard horizontally and then tighten the bolts. (Lock)

Step 3:Connect the Upper link of backboard (6) and rebounding bolts with socket head bolts (29), spring washer (30), flat washer (31) adjust the bolt in rebounding bolts lateral, reoccupy hex bolt (33), flat washer (34), locknut (35) upper lever to the lower and upper rods at the same time on the boom (Unlock).

Step 4:Insert one end of the lower link of backboard (7) welded u-shaped iron plate into the rectangular tubes on both sides of the middle part of the extension arm, and then fix it with a semicircular head hexagon bolt (32);Fix the lower rod joint with hex bolts (26), spring washers (37), flat washers (28) and threaded holes under the backboard (not locked), then adjust the lower rod adjusting bolts (14) to keep the backboard in one plane, and then tighten the hex bolts (26).

(2)Basketball rack debugging

1. Height of backboard

After lifting the basketball rack to the final position, measure the parallel, vertical and balanced parameters related to the rebound height of the machine. If the rebound is high or low, slightly loosen or tighten the adjusting bolt (37) below the back post (3) with a hook wrench to make the upper edge of the basket reach the specified elevation (3.05 meters).

2. Degree of parallelism under the backboard

Adjust the parallelism of the backboard along the bottom parallel to the court to lower the basket frame, loosen the hex bolt a little (21), swing the backboard left and right to be parallel to the ground, and then tighten the hex bolt (21).

3. Backboard flatness

If an Angle of the rebound and the overall is not in the same level, you can loosen the hex bolt (29) or hex bolt (26) of the tie rod and the rebound joint at that Angle, and adjust the tie rod joint accordingly until the whole plane is basically flat. Finally, tighten the loose bolt. When installing the glass backboard, don’t push or pull the upper link of backboard, should be carefully operated, so as not to damage the backboard.

4. Rebound perpendicularity

Adjust the rebound after the flatness, if the rebounds and ground plane is not perpendicular loose the hex bolt (33), adjust the position of upper link of backboard, then loosen the hexagonal nut (25), Use hex bolt (24) and open end wrench to adjust the rebound vertical to the ground, then fasten the hex bolt lock (33) and hexagonal nut locking (25).









6、OPERATION INSTRUCTION

(1)connect 220V power supply and must be grounded.

(2)Open the basket rack electrical control box lock, open the control box panel, plug in the power plug.

(3)Wheel lifting operation

1、Power on, power signal light on. Press the "oil pump start" button, motor rotation, oil pump oil transfer. At this time, the "oil pump start" button light is on.

2、When the motor oil pump is running normally, press the "wheel lift" button and the indicator light will be on. The walking wheel rises and the base rises. When reaching the design height, the circuit will be automatically disconnected, and the indicator light of "wheel lift" will be off.

3、When the basket rack needs to move, the power should be cut off in advance, and then one person should handle the direction of the joystick, from two to three people to the designated position, while moving, the ball rack should be carefully lowered before operation.

4、Switch on the power supply after the basket frame is moved in place, press the button of "take in wheel", and the indicator light will be on. Basket frame under gravity action, wheel retraction, base touchdown is in position.

(4) Basket lifting operation

1、Turn on the power, press the "oil pump start" button, the indicator light is on.When the oil pump is in normal operation, press the "basket up" button, the indicator light is on, the basket up gradually, the basket up to the standard position after the circuit automatically disconnect.

2、Unplug the power plug. Tighten the mechanical safety device 24 with a special wrench. Tighten the basket of mechanical safety device before putting it into use.

3、Basket rack lowering operation. Turn on the power, press the "basket up" button, and release the mechanical safety device (do not forget!) after the main cylinder is full of hydraulic oil.; Press the button of "basket rack down", and the indicator light will be on. At this point, the front post, rear post will gently lean back. If it is unable to lean back, one person can push the front pillar of the basket rack backward, so that the upper (upper bracket) will slowly fall down from the gravity. When it is stable, press the "oil pump stop" button.

7. MAINTENANCE GUIDE

Debugging:

(1)Check whether all tubing connections are correct.

(2)When refueling through the air filter port of the oil tank, the hydraulic oil viscosity shall be 15-68cts and shall be clean without impurities.It is recommended to use 46 # hydraulic oil, the system normal oil temperature - 10 ℃ to 50 ℃.

(3)The working pressure of the system depends on the setting value of the overflow valve. The overflow valve has been fully adjusted before leaving the factory.

(4)Use 220V voltage

(5)Check the cleanliness of oil every quarter, and replace the hydraulic oil every 3000 hours after the system is used for 100 hours.

(6)Adjusting method. This product has adjusted the system pressure before leaving the factory.The pressure relay, falling velocity, the user no need to adjust, if you need to adjust the high (low) the system pressure, the overflow valve cap spin off, clockwise direction (counterclockwise) adjustment screw, every 90 ° rotation, The pressure change is about 1.2Mpa.

8. WARRANTY

★  The whole equipment free warranty for 3 years,and the accessories cost is charged after 3 years.

★ For details, please call:8008585955 or 4008878855

9.Management And maintaining

The management units of parks, green spaces, squares and other public places and residential areas shall clearly identify the persons responsible for the management and maintenance of the equipment allocated to such public places and residential areas.

When purchasing and/or using the equipment purchased by the company, risk assessment shall be carried out jointly with the supplier to ensure that the equipment is matched with the management and environment.

★ The installation of equipment shall be checked and accepted jointly by the user and the relevant manufacturer or dealer (see the attached table for the installation inspection form 1) can only be used after qualified.

The user unit should be equipped with trained management personnel. Managers should have basic knowledge and management knowledge related to equipment, such as: brand, name, function, scope of application, safe service life, correct use method, common mechanical and electrical knowledge, related precautions and safety warning requirements.

The user should establish a corresponding management system and inspection and maintenance system, including daily inspection and annual inspection requirements and make detailed records (see Attachment 1). If the equipment is found to be damaged or there are unsafe factors in the daily inspection and the unit cannot solve the problem, it should immediately be listed on the obvious position of the equipment and stop using it. At the same time, notify the dealer to carry out maintenance and repair according to the annual inspection form (see attached table 2).

For equipment that exceeds the safe service life, the user should be responsible for the timely dismantling and dismantling.

The superior management department of the use unit shall conduct regular or irregular supervision and inspection.

The shaft, nut, and transmission used on the equipment should be lubricated regularly to improve the service life of the equipment. For example: coating or dipping in grease, etc.

The vulnerable parts listed in this equipment should be inspected frequently; the defective parts should be replaced in time or the equipment should be disabled until repaired.


10.MAIN COMPONENT MATERIAL LIST

No.

Name

Manufacturer

Tel.

1

Base

Shuhua Sports Co., Ltd.

4008878855

2

Column

Shuhua Sports Co., Ltd.

4008878855

3

Arm

Shuhua Sports Co., Ltd.

4008878855

4

Bumper Bar

Shuhua Sports Co., Ltd.

4008878855

5

Glass Backboard

Zhangjiagang Chengshang Sports Equipment Co., Ltd.

+8613913292381

6

Sheath

Shuhua Sports Co., Ltd.

4008878855

7

Backboard Batten

Zhangjiagang Chengshang Sports Equipment Co., Ltd.

+8613913292381

8

Basket

Hebei Hongkang Sports Equipment Co., Ltd.

+8615733777003


11.OTHERS

Please note that this equipment manual is subject to new revision or release without prior notice.

The final interpretation of this manual belongs to Shuhua Sports Co., Ltd.


12.CUSTOMER SERVICE ADDRESS AND HOTLINE

Address: Shichun Industrial Zone, Chidian, Jinjiang City, Fujian Province

Service Hotline:800-8585955   400-8578855






Contact

Add: Shichun Industrial Park, Chidian,Jinjiang City, Fujian Province, China.
Tel:   +86-595-6858 0059  /  +86-151 5959 0132
Email: shua08@shuhua.com / shuhua06@shuhua.cn
Copyright ShuHua Sports Co.,Ltd.. All rights reserved.